• The EVOlution of Maxival® Click here to read the news.

  • TOP SPONSOR L.R. VICENZA VIRTUS Click here to read the news.

APMTF- Austenitic Stainless Steel

Steel data sheets

Choose the measure unit in which display the data:

Valbruna Grade

APMTF

Steel type

Austenitic Stainless Steel

Description of material

APMTF is an austenitic stainless steel, Titanium-stabilized, and also with added Molybdenum, which has good general and pitting corrosion resistance as well as good intergranular corrosion resistance after welding processes. This grade has been designed in order to offer a good hot plasticity (forge-ability) thanks to an exact chemical balance of elements such as Carbon, Nitrogen, Titanium and Molybdenum.

Applications

APMTF is suitable for the fabrication of many products such as flanges, valves, bolting, pump shafts, food /beverages industry equipment, storage tanks, and parts working in mild to medium corrosive environments. This grade is chosen in the case of welding processes and in applications where intermittent heating up to 870 C° can happen.

Melting practices

Argon Oxygen Decarburization

Corrosion resistance

APMTF is resistant to fresh water, many organic chemicals and inorganic compounds, atmospheric corrosion, marine environments, many products used in chemical processes, paper production equipment, and rural applications and sterilizing solutions. In sea water, this grade is more resistant to pitting than type 304/304L steels such as AISLF and similar. However, pitting and crevice corrosion may occur in environments if the chloride concentrations, pH and temperature are at determinate levels. As with other standard austenitic grades, APMTF suffers from stress corrosion cracking about forty degrees (C°) above room temperature and above certain levels of stress and halogen concentrations. Strain hardened structures increase the risk of stress corrosion cracking. It should be noted that this grade, as for every kind of stainless steel, surfaces should be free of contaminant and scale, heat tint, and passivated for optimum resistance to corrosion.

Machinability

Austenitic grades are different from Ferritic and Alloy steels and require more rigid and powerful machines in addition to the correct choice of tools, coatings and cutting fluids. The Austenite structure is prone to transform into α’Martensite caused by strain hardening of the tool on the surface of the machined piece. The knowledge of this behavior must be correctly considered when a piece requires two or several cutting steps to be finished. The layer of α’Martensite is very hard and, if the subsequent turning or milling processes work on this hardened layer, a rapid tool wear could happen. The tool must work under this layer. APMTF has a chemical balance for a suitable machining thanks to its micro-resulphured structure.

Weldability

APMTF has a special chemical composition which helps to avoid solidification cracks in the fused-zone of autogenous welds due to a special Ferrite balance. In case of filler metal welding, E /ER 316L group could be used. PWHT is generally not necessary. Its composition prevents Chromium-Carbide precipitation on the grain boundaries at temperature between 500 and 850°C. However, a stabilization heat treatment should be carried out in case of high temperature applications.

Hot working

APMTF is specifically designed for hot working and are usually supplied as billets, blooms, or ingots. No preheating is required. In Primary hot transformation processes, a high temperature homogenization of large ingots and dynamic recrystallization parameters should be rightly evaluated. In the case of open die forging of large ingots and shapes, APMTF offers a good hot plasticity if a suitable soaking and a right temperature are applied. In Secondary hot transformation processes, such as extrusion, rolling or close die forging, temperatures, strain and strain rate should be well considered because they influence the properties of the austenitic structure. Suitable strain in terms of section reduction ( for instance: 15-30%) at a lower range of hot working temperatures is recommended in order to obtain a fine grain austenitic structure which is very important for mechanical , fatigue and corrosions resistance properties and makes it easier for ultrasonic testing to detect small indications as required by several International Norms. Small forgings can be cooled rapidly in air or water.

Scroll to top